Recent content by MongoTX

  1. M

    SEGA G-Loc: complete restoration saga.

    Length is 70" Width 39" Height 74"
  2. M

    Sanwa PM 1745 image upside down

    Never mind. I figured it out. The board has two connections one is flipped and the other is normal. Hooked up to the normal and all is good. It's always good to RTFM.
  3. M

    Sanwa PM 1745 image upside down

    Just got done doing a recap on a Sanwa 1745 and am hooking it up to a different game. It was in a time crisis 3 and I'm putting it in an Area 51 max force. This monitor has a non-standard connector and I believe I have it hooked up correctly. It looks good but is just upside down. The old...
  4. M

    (SQ ARCADE) MiSTer FPGA TO JAMMA/JVS/SNAC-DB15 - MiSTer for JAMMA/JVS/SNAC-DB15 Arcade cabinets

    The LED blinks about once a second. I installed a fresh load, copied over the folder and ini config put them in the root directory and still when I go to configure the joystick it is not detected. could I have some of the switches wrong on the board? Here is a link to the USB cable I am...
  5. M

    (SQ ARCADE) MiSTer FPGA TO JAMMA/JVS/SNAC-DB15 - MiSTer for JAMMA/JVS/SNAC-DB15 Arcade cabinets

    I will work to get a better video tomorrow when its a little warmer.
  6. M

    (SQ ARCADE) MiSTer FPGA TO JAMMA/JVS/SNAC-DB15 - MiSTer for JAMMA/JVS/SNAC-DB15 Arcade cabinets

    I am going to do a fresh load of the mister software and will load the files again.
  7. M

    (SQ ARCADE) MiSTer FPGA TO JAMMA/JVS/SNAC-DB15 - MiSTer for JAMMA/JVS/SNAC-DB15 Arcade cabinets

    https://media.giphy.com/media/dKvGX9LPTrBQOqwBWK/giphy-downsized-large.gif Attached is a video of it running. If I am looking at this right then yes it is blinking. Thank you for all the help
  8. M

    (SQ ARCADE) MiSTer FPGA TO JAMMA/JVS/SNAC-DB15 - MiSTer for JAMMA/JVS/SNAC-DB15 Arcade cabinets

    From your previous response. Hello, you need to flash the kernel system that supports DB15 to support DB15. How do I flash the kernel system that supports DB15? At the same time, you must use a 9-core USB3.0 data cable. Yes brand new 9-core USB3.0 cable I have installed the mister.ini files in...
  9. M

    (SQ ARCADE) MiSTer FPGA TO JAMMA/JVS/SNAC-DB15 - MiSTer for JAMMA/JVS/SNAC-DB15 Arcade cabinets

    Ok I tried the above and no change still does not recognize the joystick or buttons attached. I went and purchased snac to db15 and still does not work. Is there changes that need to be made now I have the snac module?
  10. M

    (SQ ARCADE) MiSTer FPGA TO JAMMA/JVS/SNAC-DB15 - MiSTer for JAMMA/JVS/SNAC-DB15 Arcade cabinets

    The post above is a couple of pictures of how I have it hooked up and the error. I went into the ini and un-commented the two lines but it did not make any differences. What am I missing. Thank you
  11. M

    (SQ ARCADE) MiSTer FPGA TO JAMMA/JVS/SNAC-DB15 - MiSTer for JAMMA/JVS/SNAC-DB15 Arcade cabinets

    the controller and buttons are attached directly to the Jamma.
  12. M

    Time crisis 3 V185 board switches

    A couple of questions What are the switches used for on the v185 board? Do you have to set one of the switches for two players? Thank you!
Back
Top