What's new
By:

FS Meanwell PSU Cover Assembly w/ BLUE voltmeter and IEC rocker, custom cables...

For Sale
^ It's one of those products that you really don't think about needing...until you need it. Like "Oh shit, how am I going to get this power supply to work without it looking like a complete Frankensteined mess???". The HAS was my first supergun without a power supply already built in, so I hadn't really thought about it much beforehand. I ended up buying everything I needed to make a working setup, but it wasn't going to look near this pretty. After seeing this kit I put all the parts I had purchased in a box never to be seen again. This kit makes everything super clean-looking, easy to use, and most importantly: SAFE!!! Short of building a custom metal enclosure to house both the HAS and the power supply, this is the next best thing at a fraction of the cost.
 
Its been a while guys! Happy New Years!! ^^

I have a few people showing interest in a new batch so Im going to start a IC list here. Please post a reply or DM me in private to be added to the list. Tentative assembly date beginning January 15th (Monday). Thanks!!

#1 @Neo Geon Magician PAID
#2 @Cesart636 Unpaid
#3 @danringer PAID
#4 @9999 Damage PAID
#5 @9999 Damage PAID
 
Last edited:
In for two! Aiming for a supergun setup where I don't have to change plugs as often.

Since I already have two with your original pinout, any chance I can get some visual distinction for both the 3D printed part and cable so I don't accidentally mix and match? Or alternatively, make the new ones with the same pinout as the originals.
 
9999 Damage said:
In for two! Aiming for a supergun setup where I don't have to change plugs as often.

Since I already have two with your original pinout, any chance I can get some visual distinction for both the 3D printed part and cable so I don't accidentally mix and match? Or alternatively, make the new ones with the same pinout as the originals.
Click to expand...
Ill shoot you a DM, Im sure I can figure something out :)
 
jcmorrisii said:
Bump , cause I just built a new unit with the last parts I had in stock. :thumbsup: Have some cables for HAS / Minigun too. Shoot me a DM if you would like to scoop! :)
Click to expand...
I’ll buy it if still available (with HAS cable), PM sent
 
Just got mine. Easy install, everything works great! Thanks 🙏
 

Attachments

  • IMG_1975.jpeg
    IMG_1975.jpeg
    192 KB · Views: 133
Hey, just want to say I put together another one of these as I just got some new MW 125a PSUs in and wanted to jazz one up for my new HAS 5.0.

Since I bought this one awhile ago, and I can't remember (it's my 3rd one I think).

1. Rubber feet, do they still come with them? This box did not have it. Not a big deal, but if you stopped including them, strike out the info in the first post.
2. Too much packing! Jeez, this is better packed and protected than my CAVE PCBs. I think you can save some money and go a little bit lighter here!
3. My little screw from the MW corner that was replaced by your long one, does it go anywhere?
4. Any further thoughts on 3D printing a knob that fits in/over the power regulator? That way we can adjust power without a screwdriver
5. If you ever re-design this, I think one that fits under the PSU the length of it without adding much to end would be cool. Taller but not longer!
6. Last one, I think you should try to source black connectors like Mike has with the HAS, see pic.

Thanks again man, these are awesome. Please post when you do more!
 
Last edited:
Here is a shot of the install since no one asked... COM and Ground are not 100% the same thing, but that's how it's labeled here. NC means North Carolina and like the state, no one should go there. (kidding, kidding, I'm a Tar Heel, calm down)
IMG_7016.jpeg

Double check the side of your MW PSU to verify what "V3 and +V2" mean on yours, but it's likely +5v and +12v like in my picture.
IMG_7017.jpeg

Don't forget to double check the side and swap the input power to your country. Mine's marked as 230 and 120, not 240 and 110, but yeah, I guess that's right. In the US you can likely leave it on 230 and it will work fine. In Europe, better double check or you'll have some of that magic smoke...
IMG_7018.jpeg

Finally, if these connectors were BLACK, oh man it would look so sweet...
IMG_7055.jpeg
 
XtraSmiley said:
Hey, just want to say I put together another one of these as I just got some new MW 125a PSUs in and wanted to jazz one up for my new HAS 5.0.

Since I bought this one awhile ago, and I can't remember (it's my 3rd one I think).

1. Rubber feet, do they still come with them? This box did not have it. Not a big deal, but if you stopped including them, strike out the info in the first post.
2. Too much packing! Jeez, this is better packed and protected than my CAVE PCBs. I think you can save some money and go a little bit lighter here!
3. My little screw from the MW corner that was replaced by your long one, does it go anywhere?
4. Any further thoughts on 3D printing a knob that fits in/over the power regulator? That way we can adjust power without a screwdriver
5. If you ever re-design this, I think one that fits under the PSU the length of it without adding much to end would be cool. Taller but not longer!
6. Last one, I think you should try to source black connectors like Mike has with the HAS, see pic.

Thanks again man, these are awesome. Please post when you do more!
Click to expand...
1. Yes I need to update this as I dont have the feet anymore.
2. I go overboard with packing to ensure they arrive safely. Being a 3d Print i try to insulate it from temperature swings and damage that can be incurred while shipping. Iv shipped products for decades now and its always better to be safe, than sorry. :)
3. Nope its no longer needed, or can tape it inside the case for safe keeping.
4. Id be happy to oblige but never have gotten around to engineering it.
5. I did some test prints like this; but ultimately decided against it as the different models of PSU would require differing lengths. Also the 125 would be a little big for my print bed.
6. Iv always bought them direct from JST distributors, but never seen the black ones for sale. Perhaps its a different source? Would be open to it if someone has a link or info.

Thanks for the input and kind words! :)

I just made a new batch of 5 and have 1 left if anyone is interested. Thanks!
 
Last edited:
My lighting sucks, it's actually clear. Had my choice when I ordered and thought it would be cool since I already have a black one.
 
astro_zombie138 said:
@jcmorrisii has outdone himself yet again. This beauty just arrived today and is perfectly paired with the HAS v5 and RT-125A. Awesome product as usual! Thank you bud!
Click to expand...

XtraSmiley said:
Oh man, clear is even cooler! I was using my phone and it was tough to tell, on my laptop I can kind of see it!

I'm rocking the black!
IMG_7089.jpeg
Click to expand...

PolloLoco said:
Just received my order from @jcmorrisii and the cover is fantastic, working great with the HAS 5.0 supergun - thank you!! :thumbsup:
Click to expand...
I love to see the setups!!!! Thank you all so much for the support and kind words! :love: <3
 
You must log in or register to reply here.
Back
Top